Requests accepted 24 hours a day, 7 days a week Call 866-896-2687
Hiring a Plumber

What to Do Before a Plumber Arrives: A 10-Minute Checklist

Ten minutes of preparation limits damage, saves time on the call and helps the plumber diagnose faster. Here is the checklist, plus what never to try yourself.

If you are searching for what to do before a plumber arrives, the short version is this: stop the water if it is running, make the work area reachable, write down what you have noticed, and photograph the problem. Ten minutes spent on that limits damage and helps whoever shows up diagnose the problem faster.

One note about timing: a plumber will usually call you first to talk through the problem, and a visit gets booked from there. The checklist below is what makes that first call quick and useful.

Stop the damage first

  • Shut off the water where it is running. If a single fixture is leaking, turn the small oval or round valve under the sink or behind the toilet clockwise. If you cannot tell where the water is coming from, or it is spreading, close the main. The guide to shutting off your main water supply walks through the common valve types.
  • Know which side of the meter you are on. Most cities maintain the line up to the meter, and the pipe from the meter to the house belongs to the homeowner. The City of McKinney, for example, says a loss of water in cold weather is usually a frozen pipe on the property owner’s side. If water is bubbling up in the yard or street near the meter, call your city’s 24-hour water line instead. Frisco’s cold weather page, for one, tells residents to call Public Works about a line break.
  • Handle the water heater. If the leak is at the heater, shut off its cold-water supply, then turn a gas control to OFF or switch off the breaker for an electric unit.
  • Electricity. If water has reached outlets, appliances or the panel, turn off the breaker for that area, and only if you can reach the panel without standing in water. Do not go further than the breaker.
  • Contain what you can. Buckets, towels, and a wet-dry vacuum if you have one. Lift furniture and rugs out of the wet zone.

Clear access to the work area

A plumber can lose a surprising amount of time moving things. Before the call, clear a path from the door to the work area, about three feet of working room, and good light if the job is in a closet or garage.

  • Empty the cabinet under the sink, or move the items off the washer, water heater or access panel.
  • Unlock gates and move vehicles so a service vehicle can park close, in the driveway or on the street. Mention any HOA or gate code requirements on the call.
  • Secure pets. A friendly dog is still a tripping hazard in a tight utility closet. Put them in a bedroom or crate and tell the plumber about them when they call.
  • If the work is in the attic, note where the hatch is and whether the floor is boarded.

Gather what the plumber will ask about

Model and serial numbers. For a water heater, photograph the rating label on the side of the tank. For a tankless unit, photograph the data plate and the error code on the display. For a faucet, toilet or garbage disposal, a photo of the brand name on the fixture helps.

Photos and a short video. Take wide shots of the area and close shots of the leak, stain or fixture. A 15-second video of the sound or flow of the problem can say more than a paragraph.

Symptoms, in order. Write down what you noticed, when it started and whether it comes and goes. Useful details:

  • Is the problem at one fixture or the whole house?
  • Hot water only, cold only, or both?
  • Any noises such as banging, hissing or gurgling?
  • Any smell, discoloured water or low pressure?
  • Is your water meter moving when everything is off? The EPA’s Fix a Leak Week page suggests reading the meter before and after a two-hour period when no water is used. A change suggests a leak somewhere.

History. Previous repairs, the age of the heater, recent construction, a recent freeze, and whether this has happened before. If you are a tenant, have the landlord’s contact ready.

Questions to ask on the first call

You are allowed to ask these, and a good plumber expects them.

  1. Who will be coming, and are they licensed in Texas? The plumber should hold the right licence and pull any permit the city requires.
  2. What happens if the problem is bigger than it looks? Ask how they will tell you before additional work is done.
  3. Will I get a written estimate before work begins? The questions to ask before approving a plumbing estimate are worth reading beforehand.
  4. Is there a warranty on the work and the parts, and who stands behind it? Get the answer in writing.
  5. What do I need to have ready? They may have an access request you have not thought of.

What not to do while you wait

  • Do not pour chemical drain cleaner into a slow or blocked drain. It rarely clears the real problem, and a standing pool of caustic liquid is a hazard for the person who opens the line. A plunger is fine.
  • Do not do gas work. If you smell gas, do not look for the source. Leave the house, call your gas utility or 911 from outside, and request a plumber afterward. Never relight a pilot or adjust a gas line yourself.
  • Do not use open flame to thaw pipes. The Red Cross is explicit that blowtorches and propane heaters are not safe for frozen pipes.
  • Do not open walls or cut pipes unless you are prepared to be the one to finish the repair.
  • Do not keep running the system if something is leaking or smells wrong. Water heaters and sump equipment should be off until a pro has looked.

Getting help

If you would rather not call around, call 866-896-2687 or send a request, and a local plumber will usually call back to confirm details and book a time. They set the scope and the arrival window with you, and you review the written estimate before approving work.

Need a hand with this?

A local plumber will usually call to confirm the details, whether you’re in Frisco, McKinney, Garland or elsewhere in North Texas.

Quick answers

Should I stay home until the plumber arrives?

Plan on it for the first visit. The plumber will want to talk through the problem with someone who knows the house, and they need access to the work area. If you cannot be there, tell the plumber ahead of time who will be, and that person should be able to describe the symptoms and show where the shut-offs are.

Should I turn off the water heater if there is a leak?

If the leak is at or near the water heater, yes, after you shut off the water supply to it. For gas, turn the control to OFF or pilot. For electric, switch off the breaker for the heater. If the leak is elsewhere in the house, closing the main is usually enough and you can leave the heater alone.

Why does the plumber ask for model and serial numbers?

The numbers tell them the age, capacity and fuel type of a water heater, and whether parts are still made. That lets them bring the right parts or give you a realistic picture of repair versus replacement. The numbers are on the rating label on the side of the heater, or on the data plate of the appliance in question.

Is it safe to use chemical drain cleaner while I wait?

It is better not to. Chemical cleaners rarely clear a real blockage, they can sit in the pipe as a caustic standing pool, and they can splash on whoever opens the line next. A plunger is fine. If water is not moving at all, stop and describe what you tried when the plumber calls.

Need a plumber today?

Call or send a request. A local plumber will usually get back to you to confirm the details. Requests are accepted around the clock.

Call 866-896-2687 Request Help