Requests accepted 24 hours a day, 7 days a week Call 866-896-2687
Plumbing service

Pipe Leak, Burst Pipe & Repiping Help in Dallas–Fort Worth

Requests accepted 24/7Nine North Texas cities

A pipe leak announces itself in one of two ways. Sometimes it is sudden: a line in the attic lets go during a January freeze and water comes through the ceiling. More often it is slow: a pinhole in a copper line behind the drywall, a damp spot that keeps coming back, a water bill that keeps creeping up. Both need a licensed plumber, but the urgency and the fix are different.

Plumber True Services takes requests across North Texas for burst pipe repair, leak repair and whole-house repiping. We’ll help you find a local plumber for this work. Call 866-896-2687 or send a request, and if a plumber serving your area is available they will usually call to confirm details and schedule a visit.

If a pipe has burst: do this first

Water damage grows by the minute, so the order matters.

  1. Shut off the main water valve. It is usually at the meter box near the street or where the line enters the house. Turn it clockwise until it stops. How to shut off your main water supply walks through it.
  2. Open the lowest faucet in the house to drain pressure from the lines, and the highest one to let air in.
  3. Flip the breaker for any room where water is near outlets or light fixtures.
  4. Move what you can and start drying. Towels, a wet vac and fans in the first hour prevent most of the mould that shows up a week later.
  5. Then request a plumber. Tell them where the pipe is and whether the water is off.

If water keeps coming after the main is closed, the valve may not be shutting fully; that is an emergency plumbing request. The longer checklist is in How to handle a burst pipe.

Why pipes fail in DFW homes

North Texas winters are mild most of the time, which is exactly why a hard freeze does so much damage: the houses are not built for it. Supply lines run through unheated attics, through exterior walls with little insulation, and out to hose bibs with no frost-proof fitting. A day or two below freezing is enough to split them, and the leak usually shows up as the ice thaws rather than during the freeze.

Freezes are not the only cause. The pipe material in your walls has a lot to do with how and when it fails:

Material Typical era How it fails Usual fix
Galvanised steel Before about 1970 Corrodes inside, narrows, rusts through at threads; brown water, low pressure Repipe; spot repairs rarely hold
Copper 1960s onward, still used Pinhole leaks from internal pitting, mostly on hot lines and under slabs; freeze splits Section replacement; repipe if leaks recur
Polybutylene (grey plastic, often stamped PB2110) Roughly 1978 to 1995 Turns brittle and splits, often at fittings, with little warning Full replacement is the standard advice
PEX Late 1990s to now Rare; usually at fittings, or from rodent or UV damage in attics Section repair

Polybutylene deserves particular mention. It went into a great many Dallas–Fort Worth homes during the building booms of the 1980s and early 1990s, and with it the question is when it fails, not whether. If your home is from that window and you see grey plastic supply lines near the water heater or under sinks, ask a plumber to confirm what it is.

Signs a pipe is leaking behind the walls

Not every leak is a flood. Watch for:

  • A water meter that turns with every fixture off. This is the single most reliable check.
  • Stains or bubbling paint on a ceiling or wall, especially below a bathroom or near the water heater.
  • A musty smell in a closet or cabinet that was not there before.
  • Warm or damp flooring, which may point to a slab leak rather than a wall leak.
  • Pressure that has dropped at one fixture or throughout the house.

A plumber with leak detection equipment can usually find a hidden leak without opening more wall than necessary. If the symptoms point to the line between the meter and the house, see main water line repair instead.

Burst pipe repair, section repair or repipe

For a single break on an otherwise sound system, the plumber cuts out the damaged section and splices in new pipe, usually a short run of PEX or copper with the appropriate fittings. The drywall is patched afterwards, often by a separate trade.

A repipe replaces every supply line in the house. It is the right call when the pipe is galvanised steel or polybutylene, when copper has had its third or fourth pinhole, or when a remodel already has walls open. Modern repipes in North Texas almost always use PEX run through the attic and down the walls, because it tolerates freezing better than rigid pipe and has fewer joints. The plumber should pull a permit for it.

Getting ready for the next freeze

An afternoon of work in autumn prevents most burst-pipe calls:

  • Fit foam sleeves on exposed pipe in the attic, garage and crawl space, and on the lines at the water heater.
  • Cover every hose bib with an insulated cap and disconnect hoses.
  • During a hard freeze, open cabinet doors under sinks on exterior walls and let a faucet drip.
  • If the house will be empty, shut off the main and drain the lines.

More seasonal checks are in Plumbing maintenance tips for Texas homeowners.

What happens after you call or send a request

  1. Tell us the problem and your address or ZIP. Call or use the request form. Describe the symptoms and where in the house they show up.
  2. A local plumber usually calls you back. If a plumber who handles pipe repair and repiping is available in your area, they usually call to confirm the details and book a time.
  3. Review the written estimate. The plumber gives you an estimate in writing, and no work starts until you approve it.

Where we take pipe repair requests

Freeze-related requests come from everywhere after a cold snap, with newer homes in Little Elm, Aubrey and Frisco just as exposed as older ones because of attic-run plumbing. Repipe requests for galvanised and polybutylene lines are more common in the established neighbourhoods of Denton and McKinney. See all North Texas service areas.

Related help: Leak detection, Slab leak repair, Emergency plumbing and Plumbing installation.

Pipe Leak & Burst Pipe Repair: common questions

What should I do first if a pipe bursts?

Shut off the main water valve, then open a low faucet to drain the lines. Turn off the breaker to any room where water has reached outlets or light fixtures. Move furniture and start drying with towels and fans while you request a plumber. If you can't find the main or it won't close, say so when you call; that changes how urgently a plumber needs to get there.

Why do pipes burst in North Texas when winters are mild?

Because the houses aren't built for cold. Supply lines in DFW homes commonly run through unheated attics and exterior walls with little insulation, and hose bibs are often not frost-proof. A couple of days below freezing is enough to freeze standing water in those lines, and the expanding ice splits the pipe. Most bursts are discovered when the ice thaws and the water starts flowing.

What is polybutylene pipe and should it be replaced?

Polybutylene is a grey plastic supply pipe, often stamped PB2110, that was installed in a large number of homes built from roughly 1978 to 1995, including many across Dallas–Fort Worth. It becomes brittle over time and fails at fittings and along its length with little warning. The standard recommendation is to replace it with PEX or copper rather than repair it piece by piece, and some insurers ask about it when writing a policy.

What causes pinhole leaks in copper pipe?

Pitting corrosion on the inside of the pipe, which eats through the wall at a single point. Water chemistry, high velocity through undersized pipe, stray electrical current and poor installation (too much flux, burrs left at cuts) all contribute. One pinhole is repaired by replacing that section. When a house has had several, the rest of the copper is usually in the same condition and a repipe becomes the better investment.

Is a repipe worth it, or should I just fix the leak?

Fix the leak if the pipe is PEX or sound copper and this is the first failure. Repipe if the pipe is galvanised steel or polybutylene, if copper has leaked more than twice, or if you are already opening walls for a remodel. A repipe costs more up front but ends the cycle of repairs and drywall patches. Ask the plumber to show you the failed section and explain the material before you decide.

How long does a whole-house repipe take?

For a typical single-storey house, the plumbing side is usually a few days, with water restored each evening in most cases. Two-storey homes, homes with finished ceilings everywhere and homes where the old lines run under the slab take longer. The plumber should pull a permit and schedule an inspection, and drywall repair is often a separate step by a separate trade.

Need pipe leak & burst pipe repair help today?

Call or send a request about pipe leak & burst pipe repair. A local plumber will usually get back to you to confirm the details. Requests are accepted around the clock.

Call 866-896-2687 Request Help