Most plumbing leaks announce themselves with a drip you can see. The expensive ones don’t. A pinhole in a copper line inside a wall, a cracked fitting above a ceiling or a hot-water line leaking under the slab can run for weeks before a bill, a stain or a warm patch of floor gives it away. Leak detection is the work of finding exactly where that water is going before anyone cuts into a wall or breaks a floor.
Tell us what you’ve noticed, how long it has been going on and where you are in North Texas, and we’ll help you find a plumber who locates leaks in your area. If one is available, they usually call you to confirm details and book a visit.
Signs of a hidden leak
Any one of these is worth a closer look. Two or more together usually means a leak.
- A water bill that climbs with no change in how you use water.
- The meter moves when every fixture and the irrigation system are off.
- The sound of running water in a quiet house.
- A warm spot on a tile or concrete floor, which points to a hot-water line under the slab.
- Damp drywall, bubbling paint or a stain on a wall or ceiling, especially below an upstairs bathroom.
- A musty smell in a room or cabinet with no obvious source.
- A patch of lawn that stays green or soggy when the rest is dry, or water surfacing near the meter box.
- New cracks in floors or drywall, or doors that have started sticking, on a slab foundation.
What you can check yourself first
Start with the meter test described in the FAQ below. It takes an hour and tells you whether water is leaving the system at all. Then:
- Check every toilet. Put a few drops of food colouring in each tank and wait 20 minutes without flushing. Colour in the bowl means the flapper is leaking, and that alone can explain a high bill.
- Look under every sink and behind the washer for damp cabinet floors or mineral crust at fittings.
- Check the water heater drain pan and base.
- Walk the yard between the meter and the house after a dry spell.
If the meter stops when you close the house shut-off valve, the leak is inside. If it keeps moving, the leak is in the buried service line between the meter and the house, which is a water line repair rather than an indoor one.
Where leaks hide in North Texas homes
- Inside walls. Supply lines to showers, tubs and exterior hose bibs. Freeze damage from a winter storm often shows up here months later as a slow drip.
- Above ceilings. Upstairs bathroom supply lines, tub drains and shower pan failures. The stain appears some distance from the leak because water runs along joists before it drops.
- In the yard. The service line from the meter to the house, irrigation lines and the hose bib connection.
- Under the slab. Most DFW homes sit on concrete slabs over expansive clay that swells when wet and shrinks when dry, stressing the copper lines beneath. Hot-water lines go first because heat speeds up corrosion. A confirmed under-slab leak is handled as a slab leak repair; our guide on how to tell if you have a slab leak covers the specific signs.
How plumbers find leaks without opening every wall
| Method | How it works | Best for |
|---|---|---|
| Pressure and isolation testing | Sections of the system are closed off and watched for pressure loss | Confirming a leak exists and whether it’s hot, cold or drain side |
| Acoustic listening | Sensitive microphones pick up the sound of water escaping under pressure | Pinpointing pressurised leaks in slabs, walls and yards |
| Thermal imaging | An infrared camera shows temperature differences on surfaces | Hot-water leaks, wet insulation, tracing water paths behind drywall |
| Moisture meters | Measure water content in drywall, wood and flooring | Mapping how far damage has spread |
| Camera inspection | A camera is fed through a drain line | Leaks on the drain side rather than the supply side |
A reliable plumber uses more than one method and should be able to tell you where the leak is, within a small area, before quoting the repair. If a repair is proposed without the location confirmed, ask how they know.
Why timing matters
Water damage compounds. Drywall and framing wet for more than a day or two can start to grow mold, wood and laminate flooring swell and lift, and water under a slab washes out soil and contributes to foundation movement. Finding a leak early is cheap compared with what it prevents.
If water is actively dripping or spreading, close the main shut-off valve first; our guide on how to shut off your main water supply shows where to look. A burst or gushing line is an emergency request, not a leak-detection one.
What happens after you call or send a request
- Tell us the problem and your address or ZIP. Call 866-896-2687 or use the request form. Mention what you’ve seen, whether the meter moves with the water off and how long it has been going on.
- A local plumber usually calls you back. If a plumber who does leak detection is available in your area, they usually call to confirm the details and book a time.
- Review the written estimate. The plumber gives you an estimate in writing, and no work starts until you approve it.
Where we take leak detection requests
Hidden-leak requests come from every part of Dallas–Fort Worth, from newer slab-built neighbourhoods in Frisco, Allen and Little Elm to established homes in Grapevine. Not on the list? See every North Texas area we cover.
Before the plumber arrives
- Write down the meter reading and the time, and note whether the indicator was moving.
- List everything you’ve noticed, with dates, and photograph stains or wet spots.
- Clear access to the water heater, the main shut-off and the areas you’re worried about.
- Don’t open up a wall or ceiling yourself. The plumber needs to see the surface as it is.
Once the leak is located, the repair itself may be a straightforward pipe repair. More in our guide: Signs of a hidden plumbing leak.