Requests accepted 24 hours a day, 7 days a week Call 866-896-2687
Leaks

What Causes Low Water Pressure in a House (and How to Fix It)

Weak flow at one faucet is usually a clogged aerator. Weak flow everywhere points to a valve, regulator, leak or old pipe. Here is how to sort out which.

If you are dealing with low water pressure in your house, the first question is how widespread it is. Weak flow at one faucet or one shower is almost always a clogged part at that fixture. Weak flow everywhere points to something upstream: a valve, a regulator, a leak, an aging pipe, or occasionally the city supply.

The good news is that several of the likeliest causes can be checked in an afternoon with a bucket, a bottle of vinegar and a pressure gauge that costs little at a hardware store. This article walks through the causes in the order worth checking them, so you can either fix the problem or hand a plumber a useful description.

Start by sorting one fixture from the whole house

Run water at every tap and note where it is weak. Check hot and cold separately at each one.

  • One fixture, hot and cold both weak: the aerator, showerhead or the fixture itself.
  • One fixture, only hot weak: often the hot-side shutoff or a partly clogged cartridge. If every hot tap is weak but cold is fine, look at the water heater and its valves.
  • Several fixtures or the whole house: valves, the pressure-reducing valve, a leak, corroded pipe, or the supply from the street.

That single step narrows the field more than any other. Write it down before you start unscrewing things.

Scale in aerators and showerheads

Unscrew the aerator at the tip of a faucet and look at the mesh screen. If it is crusted with white or tan grit, you have found a likely cause. The North Texas Municipal Water District describes its treated water as moderately hard, and Garland’s 2025 water quality report lists total hardness for the NTMWD supply in a range of 96 to 200 ppm. Those dissolved minerals leave scale wherever water is forced through a small opening.

Soak the aerator or showerhead in white vinegar for an hour, scrub with an old toothbrush and rinse. If the flow returns, you are done. If a faucet is old and the inside is the problem, faucet and sink repair help covers cartridges and fittings.

Partly closed valves

Check the shutoff valves before assuming something is broken.

  • The fixture shutoffs under sinks and behind toilets should be fully open.
  • The house shutoff, usually in the garage, a utility closet or near the front hose bib, should be fully open. A gate valve that was only partly reopened after a repair is a common culprit.
  • The valve at the meter belongs to the utility. Do not operate it yourself; use the house-side valve instead.

A valve that looks open can still be restricted if it is old and the gate has deteriorated. If turning the handle does nothing, or the stem is stiff or wet, leave it for a plumber.

A failing pressure-reducing valve

Many homes have a pressure-reducing valve (PRV), a bell-shaped brass fitting near where the main enters the house, which steps street pressure down to a level the plumbing can handle. When the PRV fails it can stick closed, giving weak pressure everywhere, or stick open, giving high pressure that rattles pipes and shortens the life of fixtures and the water heater.

Test the pressure with a gauge

A hose-bib pressure gauge is the one tool worth buying. Close all fixtures, thread the gauge onto an outdoor hose bib and open the bib fully. Read the needle, then check it again after a few minutes.

  • A low reading with everything off means the problem is upstream of that bib.
  • A reading that climbs over time suggests a PRV that is failing to hold.
  • A very high reading is also a problem even if flow seems fine; plumbing codes generally expect a regulator when static pressure runs high, and your fixture and heater manufacturers publish their own limits.

Do not adjust or replace a PRV without knowing what you are doing. A wrong setting can damage appliances.

A hidden leak or a slab leak

A leak in the supply line steals flow before it reaches the fixtures. EPA’s WaterSense program says the average household wastes more than 9,300 gallons a year to leaks, and its Fix a Leak Week page describes the standard check: stop all water use for two hours, compare meter readings, and treat any change as a probable leak.

If the meter moves while everything is off and the pressure has dropped, take that seriously. The guide to signs of a hidden plumbing leak lists what else to watch for, and the slab leak article covers lines under the foundation.

Corroded galvanized pipe

Galvanized steel supply pipe rusts from the inside. Over decades the interior narrows, so flow drops even though the pipe looks fine from outside. Rust-colored water at first use in the morning is a hint. Census estimates put Garland’s median home at 1978, and 53.3% of its units date from 1950 to 1979, the era when an original galvanized line can still turn up in a house that has never been repiped. Irving’s eastern side has older neighborhoods too.

Galvanized pipe cannot be cleaned out. The options are sections of pipe repair or a repipe, and a plumber will explain which suits the house.

City-side problems

Sometimes the cause is not in your house at all. If neighbors have the same issue, if pressure dips at the same time every day, or if it changed right after street work or a main break, contact your water utility. The city or district maintains the main and the connection to the meter, and the homeowner owns the line from the meter to the house, so the utility can tell you quickly which side of the meter the issue sits on.

When to request a professional

Stop the do-it-yourself checks and ask for help when:

  • The meter moves with everything closed.
  • The gauge reading is high, unstable or climbing.
  • The PRV is old, noisy or dripping.
  • You suspect galvanized pipe or a line break outside.
  • Pressure fell suddenly and you see wet soil, a soggy lawn or a warm spot on the floor.

For a suspected buried supply line, water line repair is the relevant service, and leak detection finds the leak without digging up the yard.

Getting help

If you would rather not call around, call 866-896-2687 or send a request, and a local plumber will usually call back to confirm details and book a time. You review the written estimate before approving work.

Need a hand with this?

A local plumber will usually call to confirm the details, whether you’re in Garland, Irving, Allen or elsewhere in North Texas.

Quick answers

Why is the water pressure low in just one bathroom?

When only one bathroom or one fixture is weak, the cause is almost always local: a clogged aerator or showerhead, a partly closed fixture shutoff under the sink, or a worn cartridge. The rest of the house is fine, so the main line, the regulator and the city supply are not the problem. Start with the aerator and the little shutoff valve under the sink.

Can hard water cause low water pressure?

Yes, at the fixture level. NTMWD describes the treated water most of the northern suburbs receive as moderately hard, and the minerals leave scale in aerators, showerheads and the inlet screens of valves. Scale builds slowly, so the flow seems to weaken gradually until a vinegar soak or a new part restores it.

How do I know if my pressure-reducing valve has failed?

A failing pressure-reducing valve (PRV) can swing either way: pressure that is weak all over the house, or pressure that is far too high, with banging pipes and dripping fixtures. The reliable check is a gauge on an outdoor hose bib, read with no water running. If the number looks wrong, or creeps upward over a few minutes, the valve needs a professional look.

Could low pressure mean I have a leak?

It can. A leak in the supply line bleeds off flow before it reaches your fixtures, so sudden low pressure with no other change is worth a meter test. With every fixture closed, if the meter still moves, water is leaving the system somewhere. EPA's WaterSense program suggests a two-hour check for exactly this.

Is low water pressure the city's problem or mine?

Generally the city or district maintains the main and the line to the meter, and the homeowner owns the pipe from the meter to the house. If neighbors on your street have the same problem, or the pressure drops at predictable times of day, call your water utility first. If only your house is affected, the cause is on your side of the meter.

Need a plumber today?

Call or send a request. A local plumber will usually get back to you to confirm the details. Requests are accepted around the clock.

Call 866-896-2687 Request Help