Why Your Toilet Keeps Running (and How to Stop It)
A running toilet is almost always a flapper, a chain, a float or a fill valve. Here is how to find which one, fix it with a kit, and know when to call for help.
If you have searched “why does my toilet keep running,” the answer is almost always one of four parts inside the tank: the flapper, the chain, the float and fill valve, or the overflow tube. All four are inexpensive, all four are visible when you lift the lid, and three of them you can fix in an afternoon with a basic repair kit from any hardware store.
The fix matters more than the annoyance suggests. The EPA’s WaterSense program says toilets account for nearly 30 percent of an average home’s indoor water use, and that an old or worn flapper “can cause your toilet to flush on its own or silently leak thousands of gallons a year.” The same program puts the average household’s leaks at more than 9,300 gallons a year, with toilets often the culprit.
First, confirm the leak with a dye test
Not every running toilet is obvious. Some run silently, refilling for a few seconds every half hour. The dye test catches those.
- Lift the tank lid and set it somewhere safe.
- Put several drops of food colouring (or a dye tablet from a hardware store) into the tank water. Do not flush.
- Wait 10 minutes.
- Look in the bowl. If colour has appeared, water is leaking from the tank into the bowl, almost always past the flapper.
- Flush to clear the dye before it stains.
If the bowl stays clear but you still hear the tank refilling on its own, the problem is more likely the fill valve or the float setting.
Why your toilet keeps running: the four usual causes
The flapper
The flapper is the rubber or silicone seal at the bottom of the tank that lifts when you press the handle and drops to seal the flush valve. Over time it warps, hardens, grows mineral deposits or picks up grit, and no longer seals. Water trickles into the bowl, the level drops, the fill valve turns on, and the cycle repeats. WaterSense recommends checking the flapper periodically and replacing it at least every five years.
Check: reach in and press down on the flapper. If the running stops, the flapper is the problem. Also run a finger around the seat it sits on; a rough or crusted seat will defeat a new flapper too.
The chain
The chain connects the handle arm to the flapper. Too short and it holds the flapper slightly open; too long and it can slip under the flapper and prop it up. Either way the seal fails.
Check: with the tank full, the chain should have about a half inch of slack. Move the clip on the handle arm to adjust it.
The float and fill valve
The fill valve is the tall assembly on the left side of the tank. Its float (a cup that slides on the valve body, or a ball on an arm in older toilets) tells the valve when to stop. If the float is set too high, water keeps rising until it spills into the overflow tube and the valve never shuts off. If the valve’s internal seal is worn, it hisses and leaks even when the float says stop.
Check: look at the water line. It should sit about an inch below the top of the overflow tube; most tanks have a fill line stamped inside. Lift the float gently. If the hissing stops, lowering the float setting (a screw or clip on the valve) will fix it. If it does not stop, the valve needs replacing.
The overflow tube
The overflow tube is the open vertical pipe in the middle of the tank. It is a safety drain, but if it is cracked below the water line, or a replacement is too short, water runs down it constantly.
Check: water should never be entering the top of the tube while the fill valve is off. If it is, lower the float. If the tube is cracked, the whole flush valve assembly has to come out, which means removing the tank.
Phantom flushing
If the toilet refills on its own every so often without being touched, that is phantom flushing. It is a slow flapper leak: the bowl takes the water, the tank level drops to the trip point, and the fill valve runs for a few seconds. The dye test will confirm it, and a new flapper nearly always ends it.
What a repair kit will fix, and what it will not
A universal flapper, a fill valve and a handle-and-chain assembly cover the large majority of running toilets. Turn off the supply valve behind the toilet, flush to empty the tank, swap the part, and turn the water back on. Match the flapper to the flush valve size (two-inch and three-inch are the common ones) and, on a WaterSense or dual-flush toilet, use the manufacturer’s part so the flush volume stays correct.
Request a professional instead when:
- The new flapper still leaks. The flush valve seat is pitted or scaled. Replacing the flush valve means pulling the tank, and the tank-to-bowl gasket and bolts usually need replacing at the same time.
- The shutoff valve behind the toilet will not close or starts leaking when you turn it. Old multi-turn stops seize, and forcing one can snap it.
- The tank is cracked or the bolts are corroded through.
- Water is on the floor around the base rather than in the bowl. That is a wax seal or a cracked bowl, a different problem, and it can damage the subfloor if left.
- The toilet is old enough that parts are hard to find, or you are considering a replacement anyway. The toilet repair service page covers the repair-versus-replace question.
A note on hard water
Much of Dallas–Fort Worth receives water the North Texas Municipal Water District describes as “moderately hard.” The minerals leave a crust on flapper seats and inside fill valves over the years, which is why these parts tend to need attention sooner here than in soft-water regions. When you replace a flapper, wipe the seat with a soft cloth and white vinegar first so the new seal sits flat.
Getting help
If the fixes above do not stop the running, and you would rather not call around, call 866-896-2687 or send a request, and a local plumber will usually call back to confirm details and book a time. You review the written estimate before approving work.
Related reading
Sources
Need a hand with this?
A local plumber will usually call to confirm the details, whether you’re in McKinney, Frisco, Denton or elsewhere in North Texas.
Quick answers
How do I know if my toilet is leaking silently?
Put a few drops of food colouring in the tank, do not flush, and wait 10 minutes. If colour appears in the bowl, water is leaking past the flapper. The EPA's WaterSense program recommends this test and notes that a worn flapper can leak silently or make the toilet flush on its own. Flush afterward so the dye does not stain.
How much water does a running toilet waste?
It depends on how badly it is leaking, but it adds up. WaterSense says an old or worn flapper can silently leak thousands of gallons a year, and that the average household's leaks account for more than 9,300 gallons of water wasted every year, with toilets often the culprit. A toilet that runs continuously is at the top of that range and will show on the next bill.
Can I replace a toilet flapper myself?
Yes, and it is one of the easier plumbing jobs in a house. Turn off the supply valve behind the toilet, flush to empty the tank, unhook the old flapper from the overflow tube pegs and the chain, and hook on the new one. Match the size (two-inch and three-inch flush valves are the common ones) and use the manufacturer's part on a WaterSense or dual-flush toilet so the flush volume stays right.
Why does my toilet still run after a new flapper?
Usually one of three things: the flush valve seat under the flapper is pitted or crusted with scale so the new flapper cannot seal, the float is set too high and water is spilling into the overflow tube, or the fill valve itself is worn and hissing. Check the water line against the fill mark first. If the seat is the problem, replacing the flush valve means removing the tank, which is a reasonable point to request a professional.
Need a plumber today?
Call or send a request. A local plumber will usually get back to you to confirm the details. Requests are accepted around the clock.